Pololu Qik 2s9v1 Instrukcja Użytkownika

Qik 2s9v1 User's Guide1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Demo ModeIf you short pin A to pin B (the circular pads right next to the silkscreen labels) and reset the qik, it enters demomode and remains in demo

2. red ON and green OFF3. red OFF and green ON4. red and green OFFThis cycle takes several seconds, and each of the four LED states corresponds to a d

4. Serial InterfaceYou can use the serial interface for three general purposes: querying the qik for information, setting itsconfiguration parameters,

Note: These lines are not compatible with RS-232 serial, which is inverted and uses voltages thatwould be out of spec (e.g. -12V to 12V). To connect t

Pololu Protocol:This protocol is compatible with the serial protocol used by our other serial motor and servo controllers. As such,you can daisy-chain

5. Serial Commands5.a. 0x81: Get Firmware VersionCompact protocol: 0x81Pololu protocol: 0xAA, device ID, 0x01This command returns the a single ASCII b

pulled low through the LED). If shutdown-on-error configuration parameter is set to 1, motors M0 and M1 willbe stopped as a safety precaution when any

bits (which are interpreted as a number from 0 – 7). If the lower four bits are called x and the upper three bitsare called y, the equation for the le

5.d. 0x86 & 0x87: Motor M0 & M1 CoastCommand 0x86: Motor M0 CoastCompact protocol: 0x86Pololu protocol: 0xAA, device ID, 0x06Command 0x87: Mot

Command 0x8A: Motor M0 ReverseCompact protocol: 0x8A, motor speedPololu protocol: 0xAA, device ID, 0x0A, motor speedCommand 0x8B: Motor M0 Reverse (sp

1. OverviewThe qik 2s9v1 is Pololu’s second-generation dual serial motor controller. The compact board allows anymicrocontroller or computer with a se

6. Cyclic Redundancy Check (CRC) Error DetectionFor certain applications, verifying the integrity of the data you’re sending and receiving can be very

Steps 3, 4, & 5:_______________________________________________1 0 0 0 1 0 0 1 ) 1 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0XOR 1 0 0 0 1 0 0 1

}unsigned char CRC(unsigned char message[], unsigned char length){unsigned char i, crc = 0;for (i = 0; i < length; i++)crc = CRCTable[crc ^ message

7. TroubleshootingThe following are some suggestions for ways you can troubleshoot your qik:• Test for life: With nothing more than logic voltage conn

8. Arduino LibraryWe have written a basic Arduino library for the qik dual serial motor controllers that makes it simple tointerface the qik 2s9v1 wit

the use or to the performance of this product. This product is not designed for, and should not be used in,applications where the malfunction of the p

2. Contacting PololuYou can check the qik 2s9v1 dual serial motor controller page [http://www.pololu.com/catalog/product/1110] foradditional informati

3. Connecting the QikConnecting to the qik can be as simple as hooking up logic and motor power, your motors, and RX. Manyapplications can leave the j

The qik motor controller takes two power inputs: motor power supplied via the VMOT and GND pins at thebottom of the board and logic power supplied via

Note: Even if your motor and logic power sources share a common ground, make sure you connectyour motor power supply’s ground to the GND pin just abov

3.c. Included HardwareThe qik ships with a 16×1 straight 0.100" male header strip [http://www.pololu.com/catalog/product/965], a 12×1right angle

3.d. JumpersThe qik jumpers allow you to easily alter the behavior of the device. These jumpers can be left off for mostapplications. If you use a jum