Pololu Wixel Instrukcja Użytkownika Strona 39
- Strona / 64
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Pinout
Pin Function
P0_3 ASCII_TX Serial output, transmits ASCII (0–3.3 V)
P0_2 ASCII_RX Serial input, receives ASCII (0–3.3 V, not 5 V tolerant)
P1_6 BINARY_TX Serial output, transmits arbitrary bytes (0–3.3 V)
P1_7 BINARY_RX Serial input, receives arbitrary bytes (0–3.3 V, not 5 V tolerant)
ASCII-to-Binary conversion
ASCII characters are received on the ASCII_RX pin, converted into the appropriate bytes, and then transmitted on
BINARY_TX. If you want the Wixel to send a particular byte on the BINARY_TX line, then you should send an
ASCII ‘H’ character to the ASCII_RX pin, followed by the two hex digits representing the byte. For example, if you
want the Wixel to transmit the byte 0xFA on BINARY_TX, send the three-byte ASCII string “HFA” to the ASCII_RX
line. This example can be described as:
ASCII string “HFA” → ASCII_RX → ASCII-to-binary conversion → BINARY_TX → byte 0xFA
The delimiting ‘H’ character can be omitted, but we recommend sending it at the beginning of each transmission to
make sure the Wixel is in sync with the device transmitting the ASCII. For example, to send the two bytes 0xFA and
0x1C, you could send the five-byte ASCII string “HFA1C”.
Uppercase and lowercase hex digits are both recognized. You do not need to send any newlines or other ending
delimiters to the ASCII_RX line. The Wixel transmits each byte as soon as the second hex digit is received.
Binary-to-ASCII conversion
Arbitrary bytes are received on the BINARY_RX pin and an ASCII representation of them is transmitted on
BINARY_TX. Whenever a byte is received on BINARY_RX, the Wixel will transmit three bytes on the ASCII_TX
line: the delimiting character ‘H’ is transmitted first, followed by the two hex digits representing the byte. For the
digits A–F, upper case is used. For example, if the Wixel receives 0xFB on BINARY_RX, it will transmit the three-
byte ASCII string “HFB” on ASCII_TX. This example can be described as:
Byte 0xFB → BINARY_RX → Binary-to-ASCII conversion → ASCII_TX → ASCII string “HFB”
The Wixel does not ever omit the delimiting character ‘H’ when transmitting on the ASCII_TX pin.
Serial specifications
The serial interfaces of this app are non-inverted and they use 8 data bits with 1 stop bit. This is called 8-N-1. Any
serial devices connected to the Wixel should use these same settings.
Parameters
• ascii_baud_rate: The baud rate of the ASCII interface (ASCII_RX and ASCII_TX), in bits per second. The
default value is 9600 bps. We recommend not exceeding 115200.
• binary_baud_rate: The baud rate of the binary interface (BINARY_RX and BINARY_TX), in bits per second.
The default value is 9600 bps. We recommend not exceeding 115200.
Pololu Wixel User's Guide © 2001–2014 Pololu Corporation
9. Wixel Apps Page 39 of 64
- 1. Overview 3
- Green USB LED 6
- Yellow LED 6
- 2. Contacting Pololu 8
- 3. Getting Started 9
- Wixel in bootloader mode 12
- README.txt 15
- 4. Configuring Your Wixels 20
- App Configuration 21
- Writing to a Wixel 21
- Reading from a Wixel 21
- Other Commands 22
- 5. Connecting Your Wixels 23
- VALT Power Output 24
- Low Power Considerations 24
- 3V3 Power Output 24
- 6. Using a Virtual COM Port 28
- 8. Schematic Diagram 31
- 9. Wixel Apps 32
- Default Pinout 33
- Description 33
- Indicator LEDs 34
- Control Signals 34
- General Parameters 34
- Pin Assignment Parameters 35
- Example Uses 35
- Versions 36
- 9.c. USB-to-Serial App 37
- Overview 37
- Installation Instructions 37
- ASCII-to-Binary conversion 39
- Binary-to-ASCII conversion 39
- Serial specifications 39
- Parameters 39
- Serial Commands 41
- 9.f. I/O Repeater App 44
- Default Settings 45
- 9.g. Joystick App 46
- Wixel Configuration 47
- 9.h. Wireless Tilt Mouse App 49
- Parts Needed 49
- Pinout of Transmitter Wixel 49
- Assembly 50
- Alternative Parts 51
- Mouse Speed Calculation 51
- 9.i. ShiftBrite App 51
- Using the ShiftBrite App 52
- Data Format 52
- Compiling Apps 54
- Creating Your Own Apps 56
- 10.c. Using the Eclipse IDE 56
- Advanced Features of Eclipse 57
- Hiding Unused Features 59
- Contributing your source code 60
- 10.f. Wixel App File Format 61
- The hex section 62
- The license section 62
- The description section 62
- The cdb section 62
- 11. The Wixel USB Bootloader 63
- Startup Procedure 64
Powiązane produkty i podręczniki dla Sprzęt komputerowy Pololu Wixel
(30 strony)Samsung NQ50J3530BS/EG Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Mikrowellen Samsung NQ50J3530BS/EG.
Wir stellen 1 PDF-Handbücher Samsung NQ50J3530BS/EG zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentarze do niniejszej Instrukcji